Precautions for Handling Geared Motors

●Temperature range for use:
Geared motors should be used at a temperature of -10~60℃. The figures stated in the catalog specifications are based on use atordinary room temperature approximately 20~25℃.
 
●Emperature range for storage:
Geared motors should be stored at a temperature of -15~65℃.In case of storage outside this range, the grease on the gearhead area will become unable to function normally and the motor will becomeunable to start.
 
●Relative humidity range:
Geared motors should be used in 20 - 85% relative humidity.In a humid environment, the metal parts might rust, causing abnormalities. Therefore, please be careful about use in such an environment.
 
●Turning by output shaft:
Do not turn a geared motor by its output shaft when, for example, arranging its position so as to install it. The gearhead will become a speed-increasing mechanism, which will have harmful effects, damaging the gears and other internal parts; and the motor will turn into an electrical generator.
 
●Installed position:
For the installed position we recommend a horizontal position --the position used in our company's shipping inspection.With other positions, grease might leak onto the geared motor, the load might change, and the motor's properties might change from those in the horizontal position. Please be careful.
 
●Installation of geared motor on output shaft:
Please be careful with regard to applying adhesive.It is necessary to be careful that the adhesive does not spread along the shaft and flow into the bearing, etc. Moreover, do not use a silicon adhesive or other volatile adhesive, as it could harmfully affect themotor's interior. In addition, avoid press fitting, as it could deform or damage the motor's internal mechanism.
 
●Handling the motor terminal:
Please conduct the welding work in a short time.. (Recommendation: With the soldering iron tip at a temperatureof 340 - 400℃, within 2 seconds.)
Applying more heat than is necessary to the terminal can melt the motor's parts or otherwise harm its internal structure. Moreover, applying excessive force to the terminal area can put stress on themotor's interior and damage it.
 
●Longterm storage:
Do not store a geared motor in an environment where there are materials that can generate corrosive gas, toxic gas, etc., or where the temperature is excessively high or low or there is much humidity. Please be especially careful with regard to storage for lengthy periods such as 2 years or more.
 
●Longevity:
The longevity of geared motors is greatly affected by the load conditions, the mode of operation, the environment of use, etc. Therefore, it is necessary to check the conditions under which the product will actually be used. 
 
The following conditions will have a negative effect on longevity. Please consult with us. 
●Impact loads 
●Frequent starting 
●Long-term continuous operation                                          
●Forced turning using the output shaft
●Momentary reversals of turning direction                            
●Use with a load that exceeds the rated torque  
●Use of a voltage that is nonstandard as regards the rated voltage     
●A pulse drive, e.g., a short break, counter electromotive force, PWM Control               
●Use in which the permitted overhang load or the permitted thrust load is exceeded . 
●Use outside the prescribed temperature or relative-humidity range, or in a special environment
●Please consult with us about these or any other conditions of use that may apply, so that we can be sure that you select the most appropriate model.
Concact Us Now
Gear Motor Manufacturer,Planet Gearbox Manufacturer,Planet Gear Motor Manufacturer,automotive motor Manufacturer-Ningbo Twirl Motor Co.,Ltd
NO.1269 Mingshu Road,Jiangshan Industrial Zone, Yinzhou District, NingboZhejiang Province China
You can trust us
We are a professional Manufacturer in China, and we are constantly innovating so that our customers can have better products and services.
© 2018 Gobalsir Inc.        SiteMap.html    SiteMap.xml    Terms of Service      Privacy Policy
Marketing Support by Globalsir
Enter your inquiry details, We will reply you in 24 hours.
Name can't be empty
E-mail can't be empty
Company can't be empty
Phone can't be empty
Products can't be empty
Message can't be empty
Verification code error
code
Clear